WHAT’S IN THE BOX FOR ORBBEC GEMINI 335/336?
WHAT’S IN THE BOX FOR ORBBEC GEMINI 335L/336L?
CONNECTING THE ORBBEC CAMERA
-
For Orbbec Gemini 335/336
① Assemble the tripod head with the tripod, and then secure the camera onto the assembled tripod, as illustrated in Step 1 below.
② Use the USB-C to USB-A cable to connect the camera’s Type-C port, as shown in Step 2 below.
③ Connect the USB-A connector to the host using the same USB-C to USB-A cable, as shown in Step 3 below.
-
For Orbbec Gemini 335L/336L
① Assemble the tripod head with the tripod, and then secure the camera onto the assembled tripod, as illustrated in Step 1 below.
② Use the USB-C to USB-A cable to connect the camera’s Type-C port, as shown in Step 2 below.
③ Connect the USB-A connector to the host using the same USB-C to USB-A cable, as shown in Step 3 below.
GET ORBBEC VIEWER
Select and download the corresponding Orbbec Viewer based on your system and version.
LAUNCHING ORBBEC VIEWER
- After starting the Orbbec Viewer, please make sure that the tool recognizes the 3D camera, as indicated by the following image.
【Remark】If the camera is not recognized, please check to ensure that the camera and the host are properly connected. You can try disconnecting and then reconnecting the USB cable. If it still isn’t recognized, consider replacing the USB cable or verifying whether the host computer’s power supply meets the required specifications.
-
Toggle the ‘Depth’ button at the top of the tool to start and preview the depth stream.
-
Toggle the ‘Color‘ button at the top of the tool to start and preview the color stream. The color stream and depth stream will be displayed side by side.
-
Toggle the ‘IR Left’ and ‘IR Right’ buttons at the top of the tool to strat and preview the IR stream.
-
Toggle the ‘IMU’ button at the top of the tool to start and preview the IMU stream.
-
Toggle the
button on the top of each window to show the metadata information.
-
Toggle the ‘PointCloud‘ button at the top of the tool to start and preview the 3D point cloud
-
Toggle the ‘Display’ button under the ‘Image View’ menu on the left to start and preview the D2C (depth to color registration) stream. The 3D point cloud and the D2C stream will be displayed side by side.
-
The above are relevant operations for Orbbec Viewer version 1.9.4. There may be slight differences in updated versions. For detailed instructions, please refer to the Orbbec Viewer tutorial video below .
CAUTION
1. Follow the instructions carefully when operating the camera. Improper handling may lead to damage to the internal components.
2. Do not drop the camera or expose the camera to mechanical stress.
3. Do not attempt to modify the camera as such modifications may cause permanent damage or performance degradation.
4. The temperature of the camera may rise during long periods of use.
5. Do not touch the lens. Fingerprints on the lens may affect image quality.
6. Keep the product beyond the reach of children or animals to avoid accidents.
7.If the computer does not recognize the camera, verify that the cable meets the power and data transfer requirements, then replug it into the USB port to reconnect.
8. This product is classified as a Class 1 Laser Product under the international standard EN/IEC 60825-1, Edition 3 (2014).
Using controls, adjustments, or procedures other than those specified herein may result in hazardous radiation exposure.
Safety and Handling Instructions:
●Avoid powering on the product if any external damage was observed.
●Do not attempt to open any portion of this product. There are no user serviceable parts.
●Be cautious of invisible laser radiation. Avoid direct exposure to the beam.
●To maintain compliance and safety standards, do not modify or service the product. Unauthorized modifications or servicing could result in emissions surpassing the Class 1 safety level.
